Sandune24
Toyota Advanced Member-
Posts
86 -
Joined
-
Last visited
Content Type
Events
Profiles
Forums
Gallery
Everything posted by Sandune24
-
Bought this to replace model that didn’t fit I just order This to replace the one that was too short…
-
So , here’s what almost always happens, I followed the measurements from the original Dometic A/C manual I have and bingo . I’m about 2.3 “ to short to meet the foundation plate…
-
Thank you I thought the same thing when I saw the price 😂. I’m going with this method stainless self tappers. Thank you for the feedback. I’ll post after I get the done. First I have to change the gasket.
-
It has openings for the screws , my question is what type of screws/nuts or fasteners? Thank you 🙏🏻
-
Hi everyone, I just purchased a new shroud for my Dometic ac . My question it to what do I need to attach the shroud with ? It didn’t come with any clips or screws … thank you 🎃
-
I order a 24” Lippert single step. I haven’t installed it as yet as I am rebuilding the lower step in my Escaper. The step is solid and has slip grating. Stay tuned.
-
Hi If you still have the rear LEDs I’m interested. I have an 1987 Escaper. Thanking you in advance 🙏
-
Situation that I have right now is trying to open the latch on my spare tire? Also watching the feed on the mount situation too. How do I open latch to remove cover ? Thanks
-
Hi Linda , Hope you are well 😊. So, in regard to your comment stating there is the possibility of adding cross beams and going behind the cabinets to add lateral support would do the trick? As I know I will be replacing the a/c gasket too.
-
Love your mind 🙏👣💪
-
Hi WME, just saw your cargo strap solution...I have delamination around the top sides and rear. What size cargo straps did you use, I have proflex to seal with . I’ve been grappling with sealing exterior via vises, not to many options. I would prefer tackling wood rot from the interior. The cargo straps sound doable with a little more of your insight. Thanking you in advance.
-
Maineah I see that you have a ‘87 Toyota and I’m aware they are not all the same . I am trying to figure out how my fresh water tank gets filled. I found the hose attached inside was broken and attached to nothing . Below are the photos of what I found under the split couch. There is no opening to attached the city water hose. I’ve looked and tried to lift it , the only spot I see is the manufacturers sealed opening. All the connections are correct , going to the Shurflo water pump but the rest is not connected to fill fresh water tank ....any suggestions?
-
1988 Toyota Dolphin need help with filling the fresh water tank
Sandune24 replied to drblack46's topic in General Discussion
I had to replace the intake hose for my fresh water tank and inside I see no place to connect?? Any help would be appreciated 🙏 it a 1987 Escaper 😊 and I have idea what the white bucket connects too. -
Inside photos, I glued a piece of wood across where the screws from outside wasn’t grabbing. I need to get a nut set for my drill so, I can attach and close the over cab once and for all ! Inside I can visibly see rot on the aluminum floor of over cab. Photo 2 what should I fill them with before I lay the insulation?
-
When I cleaned up the cab over there was layers of 1/8 wood over the insulation . That must have been where the screws were grabbing. I have wood that fits under the aluminum frame , should I add that or just replace the insulation and 3/4 marine plywood and see if the screws will catch that wood? open to suggestions/experience and thank you 🙏 Hunkaman, Derek, and Odessey
-
This is the section from front of cab. I removed this piece and bought new Stainless steel screws. Also I replaced butyl tape too. Then the issue is, that it won’t join ? The 3rd photo is from inside, showing the gap. When the screws go in all they are catching is the floor of the cab over. I don’t think that’s how it goes. Should I place wood on the inside along that seam? Thanks