Up north mi

any body know where to get new bushings for sway bar added after new axle it is the two that go from the link to the sway bar eyelets?

HI see the 10amp charger inside the mh do you have to run wires to both batterys from inside?

I am not going to complain about the diagram it shows me exactly what I have, Mine would be a lot worse.you have a lot going on in your mh do you have a electrical degree? One reason I bought a new convertor it looked simple to hook up and the old one didn't have a battery charger when hooked the shore to power.do you have any need for a old convertor you can have it.

I seen one of these on your mh in a pic on this forum do I need another one on the main battery side?

Yes I went to the auto parts store bought some 30amp fuse it seems small for the #2 wire any suggestions

Thanks again for the info .do you get tired of newbies asking dumb questions

That was my question can I hook the POS from convertor to the aux terminal and the auxiliary battery POS to the same terminal on the isolator? That pic is the isolator I have .the isolator is closer the main battery on one side of the mh and the POS wire from convertor the aux is on the other so I want to run one wire from aux battery to the isolator with both hooked to aux terminal.man this wiring stuffed is not my strong point thanks for making it simple.

I have the convertor grounded to the frame and the auxiliary battery grounded to the engine. The hot #2 wire wire runs to the front of the mh ,I put in a new isolator it is a colehesse smart isolator it has two main terminals should the hot wire go to battery before it goes to the isolator or can the hot wire go isolator and then to battery . in other words how do I get juice to the back.I know I have to hook the main battery to one side of the isolator.

I have another question, after I installed the new convertor I ran a #2 wire form the convertor to the front of the mh that is where the auxiliary battery is.I installed a new battery isolator so does the #2 wire go to aux terminal first then to the battery or the battery then to the aux terminal ?

Thanks for the info jd

Hay JD it is a convertor is one unit with breakers one side is for 120v and the other side for 12v .I am not a electric expert just asking questions

Hey I got a question I am installing a progress dynamics 4060 all in inverter how do I ground it ? The existing ground wire goes to the framework is that good enough? Would it be better to run a new wire to the battery?

I just started the bench walls because I wanted to up grade the inverter, it has a different size than the old one ,it was easer to build a new one on the bench than in the mh.when I took the old walls out their was some rot,and I want to put down new flooring ,the list goes on and on

Totem that is what the question was have any body applied on top of the existing floor the just flooring.after reading my post it didn't sound what I was trying to say.anyway that is what I won't to do bamboo sound great you just glued it down? I am new at forms first time on any , thank for all the ideas

Hay Linda I was thinking of 3\4 inch tongue and groove hard wood flooring glued and screwed have you heard of any body doing this?

I have a sunrader it has spongy floor I know I could try to reinforce the floor underneath my question? has anybody put down wood flooring 3/4 inch the real stuff? Glued and screwed? Any suggestions?

Nice rigs I found a full floater on craigslist that has never been used I had to put new bearings in the third member. I installed it last summer with new springs thanks to the forum. Now I am going to do the front. Found used hubs from somebody from Mt pleasant mi. Got them yesterday. Have to get rims yet they are costly. thanks again everybody on the forum I could not have done it without it .l have bunch of other projects to do

Hi DJ have you put them on and tried them? I have a 1978 Mh that I would like to do any tips? Thanks brian

Hi I live in northern mi I have a1979 sunrader