shim 'n bucket

OMG, those numbers do mean something. I just thought of a quick and dirty way to confirm these sizes empirically. Remove the wire pull ring from the top of the drain plunger and drive the plunger out the bottom of the coach, through the drain hose, onto the ground. Whose up for it? I ain't pulling my drains apart again......LOL.

No. The way the hydraulic shop matched them was with a proprietary manufacturers large 4 page plastic laminated 'catalog'. You selected the width (thickness) and then laid the O-ring on a full size image reproduced on the page. The O-ring numbers were sequential and didn't really relate to a size. Mine were 108 and 112, pretty meaningless. Places like Ace Hardware list sizes but their selection is limited. These were odd ball, our local Case Tractor hydraulic shop had never stocked those sizes ever. It's best to take them in so they can be matched properly.

Oh boy, what a good question. One must remove the drain unit from the floor itself. Seems Winnebago allowed the unlimited use of goo-puckey to plug the hole in the floor caused by the 1/2" drain hose. It was a pain to cut it all out with a box cutter. Shoulda taken pics, I know..... There are 4 H2O connections at each drain that must be dis-connected. 8" cresent wrench was the best solution, with a channel lock pliers gripping the plumbing pipe to prevent it from twisting. Once the drain unit was extracted from the flooring/plumbing system, remove the wire pull rings (using a vice and pliers) and push the plunger down through the drain unit to get at the O-rings. Good luck finding them, of course they are obscure after 20 years. After a couple of tries, I wound up at a full blown hydraulics shop to match these O-rings. Try a shop that specializes in tractor/earth moving equipment etc. I spent the time to fix this issue because I got tired of leaking my fresh H2O onto the ground while camping. Water is so precious in the desert.

I have a '92 Itasca (Winnebago). This is where a pair of my drains is located (hot and cold), just aft of the pump itself. There is also another pair of drains located almost near the shower pan. You can access those drains from the door under the stove. They are located aft of the hot water tank. I just replaced the O-rings (8 total) in all 4 of my drains.

This is the Federal Reg concerning the definition of "width". " Footnote—15 (1) For the purposes of Section 393.11, the term “overall width” refers to the nominal design dimension of the widest part of the vehicle, exclusive of the signal lamps, marker lamps, outside rearview mirrors, flexible fender extensions, and mud flaps. " From: http://www.fmcsa.dot.gov/rules-regulations/administration/fmcsr/fmcsrruletext.aspx?reg=393.11 Apparently there has been some misinformation posted above about what defines "width". Width includes only the motorhome portion of the vehicle, NOT including mirrors.

The issue you are missing is clearance lights provide information to other drivers that your vehicle is over 80" in width. My thinking is you are increasing THEIR safety. I installed Superbright LED clearance lights that are visable in daylight hours as well as high output LED parking lights that act as Daytime Running Lights. I spend a lot of time on narrow mountain roads and feel it is only fair to let other drivers know in advance of my over 80" width.

In the link I posted above, it details the test and adjustment procedure for the dash pot. Starts on page EG2-237. I doubt the rubber boot has anything to do with your problem. It is just covering the shaft to keep dust, etc off the shaft itself. A new dash pot is about $53 discounted, but you would have to adjust it when you installed the new one. Might as well test and recalibrate your existing dash pot first, to see if your mechanic is correct, that it is out of adjustment.

I'll take a stab at it. Dash pot? http://personal.utulsa.edu/~nathan-buchanan/93fsm/engine/93throttle.pdf

Buy it! JD. Bad roof for $5K, what's the problem? You can flip it for the big bucks.

I paid $13,000 for a '92 Winnebago Itasca, 68K miles. Coach and appliances were in excellent condition, not a speck of rust on the chassis. What was needed, over a period of years was tires, suspension and brake work, timing belt, valve adjust and steering gear box overhaul. As well as the usual routine maintenance. My rig is pushing 100K miles now and runs like a top. I don't feel I overpaid. But 20 year old motorhomes will all require attention no matter what you pay for them.

I had no idea the stainless mesh was capable of filtering to 75 microns. Quite amazing.

Not in a Toyota A340E tranny, which is what the OP is referring to in his '93 Itasca. The filter is actually an "oil strainer" (Toyota's term) and is a screen, (similar to screen door mesh) It is easily removable for cleaning. http://personal.utulsa.edu/~nathan-buchanan/93fsm/autotrans/24onvehicl.pdf See step 4. You must be thinking of another brand of transmission.

How do I ignore certain users on this blog? Starmar is getting tiring.

This isn't the first time you have had to deal with virii on your site. It happens consistently. Passing virii to your users is irresponsible. The Cure: 1. Shut your site down now. 2. Cease and desist doing business with GoDaddy.com. 3. Cease and desist using IP.Board Forum Software. They are totally incompetent with regards to internet security. This is actually THEIR problem to begin with. If any of the above tough love solutions are not doable due to cost or labor considerations see #1. Again. Passing virii to your users is irresponsible.

That is correct. The "Oil Seal", depicted in SA127 seals diff oil from the greased bearings. Not the axle shaft gasket. Please do not post your knowledege of Dana or whatevever american axles you choose to define. This is a Toyota blog, do not apply your many years of 'Merican experience on an Asian blog. It simply does not apply. Toyota has in it's infinite wisdom chosen a different path. If you choose to ignore it, we will choose to ignore you.