gene jo

My Dolphin is a 92 with 102K miles on it. The head gasket was done by Toyota at 98K when I bought it. It runs great. During the teardown they put new belts, hoses, etc. as well a a new radiator. Live in the desert so cooling is a big thing here. It runs great, plenty of pep....and never runs hot even in the summer. I did other things like shocks, tires and had a rack welded on the back to carry a generator if needed, or just for storage. No built in generator. Being 20 years old, it has some wear...but never being out of the desert keeps the body nice. Absolutely everything works, both truck and coach. I love it....especially with the price of gas. My only complaint is when the fuel level is low the engine will bog down for a second after a sharp turn and then accelerating...can't figure out why but keeping the fuel level above 1/8 or so solves the problem.

I got the light changed by using the skinny screwdriver and bending technique. I only changed one though. Seems so simple now. Just tore out all the carpet and will be re-carpeting with some Berber I saw at Lowe's. $12 per linear foot on a 15 ft roll..plan on 4 feet in order to not have any seams. Originally there was linoleum or something similar as I can see it now and it looks not to bad, just lots of holes from previous lousy carpet installation. Wish me luck. Thanks again for all the info on the headlight.

If what I'm reading on the internet is true, changing the headlight on my 92 Toy is a major project. I've read you have to remove the grill, remove the sidelamps and even remove the front bumper to get to the lower bumper clips; clips break when trying to be removed as they are so old and fragile. What in the world were the Toyota engineers thinking when they designed this configuration? Has anyone had any experience doing what I thought would be a simple task? I would appreciate any advice. Thanks in advance.

Thanks a lot, I found it. It was listed as a 4-wheel drive brake though (Front Brake--4WD (S12 + 12 Type Disc) not sure why it's under there as it certainly isn't 4-wheel drive. Thanks again. Gene

Does anyone have the torque specs for attaching the front rotors to the back of the large front hubs on my 92 Dolphin? Also the spec for attaching the caliper and the caliper brace's larger bolts? Can't seem to find them anywhere. Thanks

Thanks for the tips....will try.

Would like to pull out the drawers on my 92 Dolphin model 900...the ones under the sink. Can't figure out how to do it though. Does anyone have any experience with this?

Thanks for the info....appreciate it, gene

My 92 Dolphin has the fold down futon type bench....I'm in the process of reupholstering the seat area. After removing seat I notice two about 4-inch or so springs that were just hanging. I think I've connected them back correctly even though one pops out every time I open or close it and at this point don't know why....it may be stretched or need the ends pinched....my question is I'm not sure if I've connected them correctly. One end was still connected to the pin with the push on retainer, but it's the other end I'm not sure of. I'll try to upload some pictures. There is a hole in the tubular frame that the spring seems to reach to and that's where I put them. If someone else has a functional seat I would appreciate any feedback. Thanks. Also, any suggestions were to get things like foam, seat springs, seat material (I know the original is probably long gone)....again, thanks.

Just returned from Vegas to San Diego and back trip. The 92 Dolphin ran just great though I've always got an ear out for new noises since the V6 has 105k on it (just had head gasket recall done at 98k). Coming across the desert at 105+ degrees there was considerable odor from the waste tank. We just use it for Number 1 body function (saves many a stop for wife), but the odor was quite apparent. After draining tank it went away. Doing some research about vent systems I found that the plain stack vent that I have does not do much for pulling vapors out of tank. I've ordered this Cyclone vent: http://www.rvpartscenter.com/ProductDetail.asp?PID=41101&SID=9&DID=54&CID=407 Has anyone had any experience with odors like this? If so, what have you done? How about the Cyclone thing.....hoping it works. Awaiting delivery from Amazon.

Will do.....I see the rotors aren't that expensive..about $42 through....I have a PEP Boys close by but every time I bring a rotor into them, it's always too thin to turn...don't know if they are telling the truth or not. I have a micrometer but not sure how much they have to take off to resurface them. I'll give it a shot though. Again, thanks.

Thanks Maineah, The NAPA site is quite informative. I have done plenty of auto brakes before but it's been awhile since I've pulled a hub to get to a rotor. I guess I'll need new seals for that. Thanks again.

My 92 Dolphin's front brakes aren't in shown in the Hayne's manual for Toyota pickups in that year span. Seems the 1 ton trucks are kind of skipped over. I tried to search the internet but haven't had any luck yet. Does anyone have a link or info with instructions on how to dismantle to get to pads and rotors? I could go in blind but instructions would give me a bit more confidence.

My 92 Dolphin's front brakes aren't in shown in the Hayne's manual for Toyota pickups in that year span. I tried to search the internet but haven't had any luck yet. Does anyone have a link or info with instructions on how to dismantle to get to pads and rotors? I could go in blind but instructions would give me a bit more confidence. sorry for the double post....don't know how to delete this one....if someone does, feel free.

Good idea, I'll try that....thanks